Jun 27, 2018
In today's podcast episode, Jonathan Romberg comes on to discuss how the Danfoss ERC 213 works and reviews its parameters with us.
10:41 – Voltage Protection
10:56 – Compressor Protection
15:15 – App 0 No predefined application
15:28 – App 1 Medium temperature ventilated refrigeration units with timed natural defrost
15:52 – App 2 Medium temperature ventilated refrigeration units with timed electrical defrost
16:03 – App 3 Low temperature ventilated refrigeration units with timed electrical defrost
16:13 – App 4 Medium temperature ventilated refrigeration units with electrical defrost (by temperature)
16:26 – App 5 Low temperature ventilated refrigeration units with electrical defrost (by temperature)
16:37 – App 6 No predefined application with a simplified list of parameters
23:12 – r00 Temperature setpoint
23:24 – r01 Differential
23:32 – r02 Min setpoint limitation and r03 Max setpoint limitation
24:02 – r04 Display offset
25:19 – r05 Display Unit (°C/°F)
25:33 – r09 Calibration of Sair
25:47 – r12 Main switch
27:17 – r13 Night set back
27:48 – r40 Thermostat reference displacement (offset temperature)
28:30 – r96 Pull-down duration and r97 Pull-down limit temperature
29:13 – A03 Delay for temperature alarm during normal conditions
30:15 – A12 Delay for temperature alarm during pull-down/start-up/defrost
31:00 – A13 High-temperature alarm limit (Cabinet/Room)
31:34 – A14 Low-temperature alarm limit
31:55 – A27 DI1 delay and A28 DI2 delay
32:17 – A37 Condenser high alarm limit
32:41 – A54 Condenser high block limit
33:45 – A72 Voltage protection enable
34:03 – A73 Minimum cut-in voltage and A74 Minimum cut-out voltage
35:04 – A75 Maximum Voltage
37:49 – d01 Defrost method
38:32 – d02 Defrost stop temperature
38:50 – d10 Defrost stop sensor
40:51 – d03 Defrost interval
41:16 – d04 Max defrost time
43:38 – d05 Defrost delay at power up (or DI signal)
44:29 – d06 Drip delay
44:49 – d07 Fan delay after defrost
45:49 – d08 Fan start temperature after defrost
47:21 – d09 Fan during defrost
47:40 – d10 Defrost stop sensor (part II)
48:16 – d18 Compressor accumulated runtime to start defrost
50:04 – d19 Defrost on demand
53:26 – d30 Defrost delay after pull-down
54:03 – F01 Fan at compressor cutout
55:00 – F04 Fan stop evaporator temperature
55:51 – F07 Fan ON cycle and F08 Fan OFF cycle
56:37 – c01 Compressor minimum ON time
56:47 – c02 Compressor minimum OFF time
57:01 – c04 Compressor OFF delay at door open
57:51 – c70 Zero crossing selection
58:37 – o01 Delay of outputs at startup
59:11 – o02 DI1 configuration
1:01:36 – o05 Password
1:02:08 – o06 Sensor type selection
1:02:27 – 015 Display resolution
1:03:31 – o23 Relay 1 counter, o24 Relay 2 counter, and 025 o24 Relay 3 counter
1:04:13 – o37 DI2 configuration
1:04:52 – o61 DI2 configuration
1:05:07 – o67 Save settings as factory
1:05:39 – o71 DO2 config
1:06:23 – o91 Display at defrost
1:07:06 – P73 DI1 input polarity and P74 DI2 input polarity
1:07:32 – P75 Invert alarm relay
1:07:59 – P76 Keyboard lock enable
1:08:30 – u00 Controller Status
1:09:37 – u01 Air temperature (Sair)
1:10:12 – u58 Compressor relay status, u59 Fan relay status, u60 Defrost relay status, and u63 Light relay status
Find out more about the Danfoss ERC 213 HERE.
Learn more about Refrigeration Technologies at refrigtech.com.
If you have an iPhone, subscribe to the podcast HERE, and if you have an Android phone, subscribe HERE.